position, move the shift lever out of Park (automatic) or release the parking brake (manual), the display will change to the normal screen.
92
*
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0),
ACCESSORY Mode is the
equivalent of ACCESSORY (I),
and ON Mode is the equivalent
of ON (II). For more
information, see pages
181
and
178
If you try to enter the customizing mode while the vehicle is moving, you will see a ‘‘MUST STOP AND SHIFT TO PARK TO CHANGE SETTINGS’’ (automatic) or ‘‘MUST STOP AND SET PARK BRAKE TO CHANGE SETTINGS’’ (manual) message and you cannot change the settings.
You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately.
To have the driver’s ID detected, make sure the driver’s door is unlocked with a corresponding remote transmitter/keyless access remote.
2010 TL09/07/29 16:58:21 31TK4610_098
Onmodelswithoutkeylessaccess system If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’
Multi-Information Display
DRIVER’S ID
U.S. model is shown.
Press the SEL/RESET button.
TM
If you want to change any vehicle control settings, select Keyless Memory Settings by pressing either INFO button ( / ), then press the SEL/RESET button. Select CHG SETTING, then press the SEL/RESET button.
▲ ▼
Refer to the table on the following pages about the settings you want to customize.
CONTINUED
93
2010 TL09/07/29 16:58:28 31TK4610_099
Multi-Information Display
Group Setup METER SETUP (P.99)
Menu Item
Description
Setting Option
Page
LANGUAGE SELECTION
Changes the language used in the display.
ADJUST OUTSIDE TEMP. DISPLAY
Changes the outside temperature reading above or below its current reading.
TRIP COMPUTER TRIP A INFO RESET
Causes trip meter A and the average fuel economy to reset when you refuel.
ADJUST ALARM VOLUME
Changes the indicator alarm volumes into three levels.
AUTO INTERIOR ILLUMINATION
Changes the interior light sensitivity to your liking.
〜
5°F
〜
3°C
*
*
*
*
0°F
0°C
ENGLISH FRENCH SPANISH 5°F − 〜 ± (U.S.) 3°C − 〜 ± (Canada) WITH REFUEL MANUAL ONLY IGN OFF HIGH MID * LOW MAX HIGH MID * ON * OFF ON OFF
*
LOW MIN OFF
100
101
102
104
105
106
109
POSITION SETUP (P.108)
KEYLESS START GUIDANCE SCREENS MEMORY POSITION LINK
*
Changes the display of the keyless start guidance screens. Changes the driver’s seat and the outside mirror positions to a stored setting.
* *
1 : 2 :
Default setting Only on models with keyless access system
94
2010 TL09/07/29 16:58:37 31TK4610_100
Group Setup
KEYLESS ACCESS SETUP (P.111)
*
Menu Item
DOOR UNLOCK MODE
KEYLESS ACCESS LIGHT FLASH
LIGHTING SETUP (P.116)
KEYLESS ACCESS BEEP
INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
* *
1 : 2 :
Default setting Only on models with keyless access system
Multi-Information Display
Description
Setting Option
Changes which doors unlock when you use the remote or grab the driver’s door handle. Causes some exterior lights to blink when you unlock/lock the doors by grabbing or touching the sensor/pushing the button on the driver’s door handle. Causes the beeper to sound when you unlock/lock the doors by grabbing or touching the sensor/ pushing the button on the driver’s door handle. Changes how long (in seconds) the interior lights stay on after you close the doors. Changes how long (in seconds) the exterior lights stay on after you close the driver’s door.
Changes the timing of when the headlights come on. The headlight switch needs to be in the AUTO position.
*
DRIVER DOOR ALL DOORS ON OFF
*
*
ON OFF
15 sec
0 sec
LOW MIN
*
*
60 sec 30 sec 60 sec 30 sec 15 sec MAX HIGH MID
*
Page
112
113
114
117
118
119
CONTINUED
95
2010 TL09/07/29 16:58:44 31TK4610_101
Multi-Information Display
Group Setup
DOOR/WINDOW SETUP (P.121)
Menu Item AUTO DOOR LOCK
Description
Setting Option
Changes when the doors automatically lock.
AUTO DOOR UNLOCK
Changes when the doors automatically unlock.
Changes which doors unlock with the remote transmitter/keyless access remote on the first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door. Set/Cancel all the customized settings as default.
KEY AND REMOTE UNLOCK MODE
KEYLESS LOCK ACKNOWLEDGMENT
SECURITY RELOCK TIMER
DEFAULT ALL (P.129)
* * *
1 : 2 : 3 :
Default setting Default setting for automatic transmission Default setting for manual transmission
96
*
*
SHIFT FROM P (A/T only) WITH VEHICLE SPEED OFF SHIFT TO P/DRIVER DOOR (A/T only) SHIFT TO P/ALL DOORS (A/T only) IGN OFF/DRIVER DOOR IGN OFF/ALL DOORS OFF DRIVER DOOR ALL DOORS
*
*
*
ON OFF
90 sec 60 sec 30 sec CANCEL SET
*
Page
122
123
125
126
127
129
2010 TL09/07/29 16:58:57 31TK4610_102
Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:
METER SETUP POSITION SETUP KEYLESS ACCESS SETUP LIGHTING SETUP DOOR/WINDOW SETUP
*
Multi-Information Display
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown on the next page. Press the INFO ( / ) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
If you do not make any changes, select ‘‘EXIT.’’ The display returns to the normal display.
*
: Only on models with keyless
access system
When you want to change the vehicle control settings, press the INFO ( / ) button to select CHG SETTING, then press the SEL/ RESET button.
▲ ▼
If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page
129
CONTINUED
97
2010 TL09/07/30 16:55:11 31TK4610_103
Multi-Information Display
DEFAULT ALL See page 129.
). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button. : On models with keyless access system only
*
METER SETUP See page 99.
POSITION SETUP See page 108.
KEYLESS ACCESS SETUP * See page 111.
LIGHTING SETUP See page 116.
DOOR/WINDOW SETUP See page 121.
98
2010 TL09/07/29 16:59:17 31TK4610_104
Meter Setup Here are the five or six custom settings for the meter setup:
LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP COMPUTER TRIP A INFO RESET ADJUST ALARM VOLUME AUTO INTERIOR ILLUMINATION Onmodelswithkeylessaccess system KEYLESS START GUIDANCE SCREENS
Multi-Information Display
See page 100.
See page 101.
See page 102.
See page104 .
See page 105.
Onmodelswithkeylessaccesssystemonly See page 106.
). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button.
CONTINUED
99
2010 TL09/07/29 16:59:26 31TK4610_105
Multi-Information Display
While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
LanguageSelection
There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired language by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
100
2010 TL09/07/29 16:59:39 31TK4610_106
AdjustOutsideTemp.Display
Multi-Information Display
U.S. models
Canadian models
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘LANGUAGE SELECTION’’ and repeat the procedure again.
If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to enter the setting.
▲ ▼
The displayed number is the current adjustment above or below the outside temperature.
Adjust the outside temperature value by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to set the desired value.
▲ ▼
CONTINUED
101
2010 TL09/07/29 16:59:51 31TK4610_107
Multi-Information Display
U.S. models
Canadian models
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again.
102
WITH REFUEL information is reset every time you refuel your vehicle.
The Trip A
−
TripComputerTripAInfoReset You can select the reset timing of the Trip A information: Trip A, Average Fuel Economy A, Average Vehicle Speed A, and Elapsed Time A.
There are three reset choices you can make:
MANUAL ONLY You can reset the Trip A information when Trip A is displayed (see page
−
81
).
−
The Trip A information
IGN OFF is reset when you turn the ignition switch to the LOCK (0) position.
*
*
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0). For
more information, see pages
178
and
181
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
2010 TL09/07/29 17:00:00 31TK4610_108
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP COMPUTER TRIP A INFO RESET’’ and repeat the procedure again.
CONTINUED
103
2010 TL09/07/29 17:00:10 31TK4610_109
Multi-Information Display
AdjustAlarmVolume
Select the warning alarm volume from three levels.
Press the SEL/RESET button to see the selections.
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Select the desired level by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST ALARM VOLUME’’ and repeat the procedure again.
104
2010 TL09/07/29 17:00:20 31TK4610_110
AutoInteriorIllumination While the headlight switch is turned on, the interior lights gradually dim, as the outside light level gets low. You can customize at which outside light level the lights start to dim.
There are MAX, HIGH, MID, LOW and MIN levels and OFF for the auto interior illumination settings.
If you want the illuminations to start dimming as early as possible, select MAX. For illuminations to start dimming as late as possible, select MIN. Choose HIGH, MID, or LOW for levels in between.
To disable the auto interior illumination function, select OFF.
Multi-Information Display
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
CONTINUED
105
2010 TL09/07/29 17:00:27 31TK4610_111
Multi-Information Display
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO INTERIOR ILLUMINATION’’ and repeat the procedure again.
106
KeylessStartGuidanceScreens
Onmodelswithkeylessaccesssystem
When this item is set to ON, you will
see some guidance messages on the
multi-information display. You can
change this setting between on and
off. For more information on start
guidance messages, see page
182
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
2010 TL09/07/29 17:00:34 31TK4610_112
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS START GUIDANCE SCREENS’’ and repeat the procedure again.
107
2010 TL09/07/29 17:00:42 31TK4610_113
Multi-Information Display
Position Setup You can customize the MEMORY POSITION LINK setting in position setup.
While ‘‘POSITION SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the custom setting then press the SEL/RESET button to enter your selection.
▲ ▼
108
See page109 .
). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button.
2010 TL09/07/29 17:00:53 31TK4610_114
MemoryPositionLink When Memory Position Link is set to ON, the driver’s seat and the outside mirrors move to the positions stored in memory. To cause the memory to activate, open the driver’s door with the remote transmitter. On models with keyless access system, open the driver’s door with the remote, or grab the door handle while carrying the remote.
To set the memory positions, see page
164
Onmodelswithkeylessaccesssystem For information on using the remote, see page
167
Multi-Information Display
You can choose this item to customize from ‘‘POSITION SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
CONTINUED
109
2010 TL09/07/29 17:00:58 31TK4610_115
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘MEMORY POSITION LINK’’ and repeat the procedure again.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
110
2010 TL09/07/29 17:01:09 31TK4610_116
Keyless Access Setup Onmodelswithkeylessaccesssystem There are three custom settings for the keyless access setup:
DOOR UNLOCK MODE KEYLESS ACCESS LIGHT FLASH KEYLESS ACCESS BEEP
While ‘‘KEYLESS ACCESS SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button, until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
Multi-Information Display
See page112 .
See page113 .
See page114 .
: Press the INFO button ( ). ▲ ▼ : Press the SEL/RESET button.
CONTINUED
111
2010 TL09/07/29 17:01:18 31TK4610_117
Multi-Information Display
DoorUnlockMode
Press the SEL/RESET button to see the selections.
Select DRIVER DOOR or ALL DOORS by pressing the INFO ( / ▲ ) button, then enter your selection ▼ by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR UNLOCK MODE’’ and repeat the procedure again.
To select whether the driver’s door or all doors unlock when you open the driver’s door with the remote or by grabbing the door handle (while carrying the remote), follow these instructions:
You can choose this item to customize from ‘‘KEYLESS ACCESS SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
112
2010 TL09/07/29 17:01:28 31TK4610_118
KeylessAccessLightFlash When KEYLESS ACCESS LIGHT FLASH is set to ON, some exterior lights blink twice when you unlock the doors by grabbing the driver’s door handle while carrying the remote.
The same exterior lights blink once when you lock the doors by pushing the door lock button while carrying the remote.
Multi-Information Display
You can choose this item to customize from ‘‘KEYLESS ACCESS SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
CONTINUED
113
2010 TL09/07/29 17:01:36 31TK4610_119
Multi-Information Display
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS ACCESS LIGHT FLASH’’ and repeat the procedure again.
114
KeylessAccessBeep When KEYLESS ACCESS BEEP is set to ON, the beeper sounds twice when you unlock the doors by grabbing the drivers door handle while carrying the remote.
When you lock the doors by pushing the door lock button while carrying the remote, the beeper sounds once.
You can choose this item to customize from ‘‘KEYLESS ACCESS SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
2010 TL09/07/29 17:01:44 31TK4610_120
Multi-Information Display
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS ACCESS BEEP’’ and repeat the procedure again.
115
2010 TL09/07/29 17:01:53 31TK4610_121
Multi-Information Display
Lighting Setup Here are the three custom settings for the lighting setup:
INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER AUTO LIGHT SENSITIVITY
While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
116
See page 117.
See page 118.
See page 119.
). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button.
2010 TL09/07/29 17:02:03 31TK4610_122
InteriorLightDimmingTime
Multi-Information Display
The interior lights fade out when you close all doors. To change how long the lights stay on before they fade out, follow these instructions:
You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select the desired setting (15 sec, 30
sec, or 60 sec) by pressing the INFO
( / ) button, then enter your
▲ ▼
selection by pressing the SEL/
RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again.
CONTINUED
117
2010 TL09/07/29 17:02:11 31TK4610_123
Multi-Information Display
HeadlightAutoOffTimer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you remove the key from the ignition switch and close the driver’s door. On models with keyless access system, the lights go off after the selected time when you close the driver’s door and take the remote with you. To change how long the lights stay on before they go off, follow these instructions:
118
You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select the desired setting (60 sec, 30
sec, 15 sec or 0 sec) by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
▲ ▼
2010 TL09/07/29 17:02:23 31TK4610_124
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘HEADLIGHT AUTO OFF TIMER’’ and repeat the procedure again.
AutoLightSensitivity The headlights automatically come on when the headlight switch is in the AUTO position and the ambient light reaches a changeable level. You can select the auto light sensitivity from the following five levels:
−
MAX The headlights come on when it is bright.
−
HIGH The headlights come on when it is somewhat bright.
−
MID The headlights come on when it is as bright as sunset or sunrise.
−
LOW The headlights come on when it is somewhat dark.
Multi-Information Display
−
MIN The headlights come on when it is dark.
You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
CONTINUED
119
2010 TL09/07/29 17:02:30 31TK4610_125
Multi-Information Display
Press the SEL/RESET button to see the selections.
Select the desired setting (MAX, HIGH, MID, LOW or MIN) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO LIGHT SENSITIVITY’’ and repeat the procedure again.
120
2010 TL09/07/29 17:02:41 31TK4610_126
Door/Window Setup Here are the five custom settings for the door setup:
AUTO DOOR LOCK AUTO DOOR UNLOCK KEY AND REMOTE UNLOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER
While ‘‘DOOR/WINDOW SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
Multi-Information Display
See page122 .
See page123 .
See page125 .
See page 126.
See page 127.
). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button.
CONTINUED
121
2010 TL09/07/29 17:02:51 31TK4610_127
Multi-Information Display
AutoDoorLock There are three settings you can choose from:
−
SHIFT FROM P The doors lock whenever you move the shift lever out of Park. (Automatictransmissionmodelonly)
WITH VEHICLE SPEED The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h).
−
−
OFF The auto door lock is deactivated all the time.
122
You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
A/T model is shown.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
2010 TL09/07/29 17:03:03 31TK4610_128
Multi-Information Display
AutoDoorUnlock There are five possible settings for automatic transmission models and three possible settings for manual transmission models.
Automatictransmissionmodelonly DRIVER DOOR WITH SHIFT TO P − you move the shift lever to Park with the brake pedal depressed.
The driver’s door unlocks when
Automatictransmissionmodelonly ALL DOORS WITH SHIFT TO P − All the doors unlock when you move the shift lever to Park with the brake pedal depressed.
A/T model is shown.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.
DRIVER DOOR WITH IGN OFF − The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position.
*
ALL DOORS WITH IGN OFF All the doors unlock when you turn the ignition switch to the LOCK (0) position.
−
*
−
OFF deactivated all the time.
The auto door unlock is
*
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0). For
more information, see pages
178
and
181
CONTINUED
123
2010 TL09/07/29 17:03:10 31TK4610_129
Multi-Information Display
You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
A/T model is shown.
Press the SEL/RESET button to see the selections.
If you choose ‘‘IGN OFF,’’ you will see the above display.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
▲ ▼
Press the INFO ( / ) button to switch the door lock mode setting between the driver’s door and all doors. Then, press the SEL/RESET button to enter your selection.
124
2010 TL09/07/29 17:03:21 31TK4610_130
Multi-Information Display
KeyandRemoteUnlockMode
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.
You can select whether the driver’s door or all the doors unlock the first time you press the unlock button on the remote transmitter/keyless access remote.
You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
CONTINUED
125
2010 TL09/07/29 17:03:31 31TK4610_131
Multi-Information Display
KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter or the keyless access remote, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the trunk are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.
). You can
376
You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEY AND REMOTE UNLOCK MODE’’ and repeat the procedure again.
When you press the UNLOCK button on the remote transmitter or the keyless access remote to unlock the driver’s door/all the doors (depending on the customize setting), the exterior lights blink twice to verify that the door(s) is unlocked and the security system is turned off.
To turn this feature on or off, follow these instructions.
126
2010 TL09/07/29 17:03:42 31TK4610_132
Press the SEL/RESET button to enter the selecting mode.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.
Multi-Information Display
SecurityRelockTimer If you unlock the doors with the remote transmitter or the keyless access remote, but do not open any of the doors within 30 seconds, the doors automatically relock, and the security system sets.
You can change this relock time from 30 seconds to 60 or 90 seconds.
Onmodelswithkeylessaccesssystem
When you unlock the doors by
touching either front door handle
while carrying the keyless access
remote, the relock time is fixed in 30
seconds.
CONTINUED
127
2010 TL09/07/29 17:03:50 31TK4610_133
Multi-Information Display
You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.
128
2010 TL09/07/29 17:04:00 31TK4610_134
DEFAULT ALL
If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button.
▲ ▼
To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button.
▲ ▼
If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display.
Multi-Information Display
When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display.
If the setting is not successfully completed, ‘‘FAILED’’ is shown for several seconds, and then the screen goes back to the normal message mode. Repeat the same procedure to select DEFAULT ALL.
129
2010 TL09/07/29 17:04:09 31TK4610_135
Controls Near the Steering Wheel
REMOTE AUDIO CONTROL BUTTONS (P. 370)
PADDLE SHIFTERS
(P. 473)
WINDSHIELD WIPERS/WASHERS (P. 131)
ENGINE START/STOP BUTTON
(P. 178)
HEADLIGHTS/TURN SIGNALS/ FOG LIGHTS (P. 133, 137)
INSTRUMENT PANEL BRIGHTNESS (P. 137)
VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P. 485) HEADLIGHT WASHERS * (P. 132)
VOICE CONTROL BUTTONS for NAVIGATION SYSTEM / BLUETOOTH HANDSFREELINK SYSTEM (P. 388, 406)
*
STEERING WHEEL ADJUSTMENTS (P. 140)
NAVIGATION DISPLAY
*
PASSENGER AIR BAG OFF INDICATOR (P. 34)
HAZARD WARNING BUTTON (P. 139)
CENTER DISPLAY (P. 217, 274) REAR WINDOW DEFOGGER/HEATED MIRROR BUTTON (P. 139, 163) INTERFACE DIAL * SELECTOR KNOB * (P. 226)
(P. 273)
HORN *
MULTI-INFORMATION DISPLAY BUTTONS (P. 78)
SEAT HEATER SWITCHES
(P. 196)
KEYLESS ACCESS REMOTE SLOT
(P. 191)
A/T model with navigation system is shown.
CRUISE CONTROL BUTTONS
(P. 382)
To use the horn, press the center pad of the steering wheel. If equipped Refer to the navigation system owner’s manual.
1 :
*
2 :
*
3 :
*
130
2010 TL09/07/29 17:04:21 31TK4610_136
Windshield Wipers and Washers
ADJUSTMENT RING
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed