Login- Download PDF Manual
-
components, so you can be confident of their performance and durability.
446
U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.
＃
According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, Acura recommends that all maintenance services be performed in accordance with the intervals indicated by the multi-information display.
Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.
Engine oil level time you fill the fuel tank. See page
Check every
383
−
Engine coolant level radiator reserve tank every time you fill the fuel tank. See page
Check the
−
383
Automatic transmission Check the fluid level monthly. See page 458
−
Brakes monthly. See page
−
Check the fluid level
460
−
Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 474
−
Check the operation of
Lights the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page
462
2010 RL ０９／０４／０２ １９：３６：１３ ３１ＳＪＡ６５０ ０４５２
Maintenance Minder
Symbol
Maintenance Main Items
Replace engine oil ＊ Replace engine oil and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items:
Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and line (including ABS) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections ＃
＊
＃
NOTE:
If the message ‘‘SERVICE DUE NOW’’ does not appear more than 12 months after the display is reset, change the engine oil every year.
See information on maintenance and emissions warranty on page
446
Independent of the maintenance messages on the multi-information display, replace the brake fluid every 3 years. Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy.
CONTINUED 447
2010 RL Symbol
Replace rear differential fluid
Maintenance Sub Items
Driving in mountainous areas at very low vehicle speeds or trailer towing results in higher level of mechanical (shear) stress to fluid. This requires differential fluid changes more frequently than recommended by the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the differential fluid changed at 7,500 miles (12,000 km), then every 15,000 miles (24,000 km).
０９／０４／０２ １９：３６：１８ ３１ＳＪＡ６５０ ０４５３
Maintenance Minder
Maintenance Sub Items
Rotate tires Replace air cleaner element
If you drive in dusty conditions, replace every 15,000
miles (24,000 km).Replace dust and pollen filter
If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000
miles (24,000 km).Inspect drive belt Replace transmission and transfer fluid
Driving in mountainous areas at very low vehicle speeds or trailer towing results in higher transmission and transfer temperatures. This requires transmission and transfer fluid changes more frequently than recommended by the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the transmission and transfer fluid changed at 60,000 miles (100,000 km), then every 30,000 miles (48,000 km).
Replace spark plugs Replace timing belt and inspect water pump
20°F,
If you drive regularly in very high temperatures (over 110°F, 43°C), or in very low temperatures (under 29°C), replace every 60,000 mile (U.S.)/ − 100,000 km (Canada). Inspect valve clearance Replace engine coolant
−
Symbol
448
2010 RL ０９／０４／０２ １９：３６：２２ ３１ＳＪＡ６５０ ０４５４
ENGINE OIL DIPSTICK (Orange loop)
WASHER FLUID (Black cap)
POWER STEERING FLUID ＊ (Red cap)
ENGINE COOLANT RESERVOIR
＊: The power steering fluid reservoir is located under the right compartment cover.
Fluid Locations
BRAKE FLUID (Black cap)
ENGINE OIL FILL CAP
AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)
RADIATOR CAP
449
2010 RL ０９／０４／０２ １９：３６：３０ ３１ＳＪＡ６５０ ０４５５
Engine Compartment Covers
The component parts in the engine compartment are protected by several covers. You may need to remove the covers when you perform some simple maintenance work.
All of the covers are secured by holding clips.
To remove the battery cover, turn the knob of the fastener and remove the holding clips by pushing on the center of each fastener head.
To remove the front bulkhead cover:
1.
Remove the battery cover.
2.
Remove the holding clips by pushing on the center of each fastener head.
450
FRONT BULKHEAD COVER
BATTERY COVER
CLIPS
CLIPS
CLIPS
KNOB
Unlock Lock
Push to remove clip Push to reset/install clip
2010 RL ０９／０４／０２ １９：３６：４０ ３１ＳＪＡ６５０ ０４５６
To remove the left engine compartment cover:
Engine Compartment Covers
RIGHT ENGINE COMPARTMENT
LEFT ENGINE COMPARTMENT
CLIPS
CLIPS
CLIP
1.
2.
Remove the battery cover (see page
450
).
Remove the holding clips by pushing on the center of each fastener head.
To remove the right engine compartment cover:
1.
Remove the battery and front bulkhead covers (see page 450
).
Remove the holding clips by pushing on the center of each fastener head.
Take the windshield washer hose out from the holder on the bottom side of the cover.
When reinstalling the covers, make sure the pins and tabs are in their proper positions.
2.
3.
Push to remove clip Push to reset/install clip
451
2010 RL ０９／０４／０２ １９：３６：４７ ３１ＳＪＡ６５０ ０４５７
Adding Engine Oil
Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20
detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements.API CERTIFICATION SEAL
Ambient Temperature
Acura Motor Oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Acura Motor Oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’ The oil viscosity or weight is provided on the container’s label. 5W-20 oil is formulated for year- round protection of your vehicle to improve cold weather starting and fuel economy.
ENGINE OIL FILL CAP
Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment.
Install the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level. Do not fill above the upper mark; you could damage the engine.
452
2010 RL ０９／０４／０２ １９：３６：５５ ３１ＳＪＡ６５０ ０４５８
Adding Engine Oil, Changing the Engine Oil and Filter
Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil, it displays the API certification seal, and it is the proper weight. You must follow the oil and filter change intervals shown on the maintenance minder display.
Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.
Changing the Engine Oil and Filter Always change the oil and filter according to the maintenance messages shown on the multi- information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.
Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.
1.
Run the engine until it reaches normal operating temperature, then shut it off.
OIL DRAIN BOLT WASHER
2.
Open the hood, and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.
453
2010 RL ０９／０４／０２ １９：３７：０５ ３１ＳＪＡ６５０ ０４５９
Changing the Engine Oil and Filter
OIL FILTER
3.
Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.
Make sure the oil filter gasket is not stuck to the contacting surface of the engine. If it is, remove it before installing a new oil filter.
4.
Install a new oil filter according to the instructions that come with it.
454
5.
6.
7.
8.
9.
Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m)
Refill the engine with the recommended oil. Engine oil change capacity (including filter): 4.5 US qt (4.3 )
Replace the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5
seconds. If it does not, turn off the engine, and check your work.Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.
Turn off the engine and let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.
Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.
2010 RL ０９／０４／０２ １９：３７：１２ ３１ＳＪＡ６５０ ０４６０
Adding Engine Coolant
RESERVE TANK
If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.
Engine Coolant
If the reserve tank is completely empty, you should also check the coolant level in the radiator.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
Always use Honda Long-life Anti- freeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent distilled water. Never add straight antifreeze or plain water.
If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
CONTINUED
455
2010 RL ０９／０４／０２ １９：３７：２０ ３１ＳＪＡ６５０ ０４６１
Engine Coolant
LID
RADIATOR CAP
1.
Lift up the lid on the front bulkhead cover from the front.
2.
When the radiator and engine are cool, relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.
3.
Remove the radiator cap by pushing down and turning counterclockwise.
4.
RESERVE TANK The coolant level should be up to the base of the filler neck. Add coolant if it is low.
Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.
456
2010 RL ０９／０４／０２ １９：３７：２４ ３１ＳＪＡ６５０ ０４６２
Engine Coolant
5.
Put the radiator cap back on, and tighten it fully.
6.
Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.
7.
Reinstall the lid.
Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.
457
2010 RL ０９／０４／０２ １９：３７：３２ ３１ＳＪＡ６５０ ０４６３
Windshield Washers, Automatic Transmission Fluid
DIPSTICK
Automatic Transmission Fluid Check the fluid level with the engine at normal operating temperature.
1.
Park the vehicle on level ground. Start the engine, let it run until the radiator fan comes on, then shut off the engine. For accurate results, wait about 60 seconds (but no longer than 90 seconds) before doing step 2.
2.
Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.
Windshield Washers Check the fluid level in the windshield washer reservoir at least monthly during normal use. If the washer fluid is low, a ‘‘WASHER FLUID LOW’’ message appears on the multi-information display. Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition them.
Do not use engine antif reeze
NOTICE: or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.
458
2010 RL ０９／０４／０２ １９：３７：４２ ３１ＳＪＡ６５０ ０４６４
Automatic Transmission Fluid
Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.
Always use Acura ATF-Z1
(automatic transmission fluid).Use only Acura ATF-Z1 (automatic transmission f luid). Do not mix with other transmission f luids. Using transmission f luid other than Acura ATF-Z1 may cause deterioration in transmission operation and durability, and could result in damage to the transmission. Damage resulting f rom the use of transmission f luid other than Acura ATF-Z1 is not covered by the Acura new vehicle warranty.
UPPER MARK LOWER MARK
3.
Insert the dipstick all the way into the transmission as shown.
4.
5.
Remove the dipstick and check the fluid level. It should be between the upper and lower marks.
If the level is below the lower mark, add fluid into the dipstick hole to bring it to the level between the upper and lower marks.
6.
Insert the dipstick all the way back into the transmission securely as shown in the illustration.
The transmission should be drained and refilled with new fluid when this service is shown by a maintenance message on the multi-information display.
If you are not sure how to add fluid, contact your dealer.
459
2010 RL ０９／０４／０２ １９：３７：５２ ３１ＳＪＡ６５０ ０４６５
Brake Fluid, Power Steering Fluid
Brake Fluid Check the brake fluid level in the reservoirs monthly.
MAX
Power Steering Fluid
UPPER LEVEL
To check the fluid level, remove the left engine compartment cover (see page
451
).
Replace the brake fluid every 3 years, independent of mileage. Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3
or DOT 4 fluid, from a sealed container, as a temporary replacement. Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible. Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.460
MIN
The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.
LOWER LEVEL
),
After removing the right engine compartment cover (see page 451
check the level on the side of the reservoir when the engine is cold. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If not, add power steering fluid to the UPPER LEVEL mark.2010 RL ０９／０４／０２ １９：３７：５８ ３１ＳＪＡ６５０ ０４６６
Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.
Always use Acura Power Steering Fluid. You may use another power steering fluid as an emergency replacement, but have the power steering system flushed and refilled with Acura PSF as soon as possible.
A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently, and have the system inspected as soon as possible.
Power Steering Fluid, Timing Belt
Turning the steering wheel to f ull lef t or right lock and holding it there can damage the power steering pump.
Timing Belt The timing belt should be replaced at the intervals shown on the maintenance minder. Replace the belt at 60,000 miles (100,000 km) if you regularly drive your vehicle in one or more of these conditions:
In very high temperatures (over 110°F, 43°C).
In very low temperatures (under 29°C).
20°F,
−
−
If you frequently tow a trailer.
461
2010 RL ０９／０４／０２ １９：３８：０３ ３１ＳＪＡ６５０ ０４６７
Lights
Headlight Aiming Your vehicle is equipped with an automatic headlight adjusting system that adjusts the vertical angle of the headlights automatically. Refer to page information.
for more
145
The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk or pull a trailer (if applicable), readjustment may be required. Adjustments should be done by your dealer or another qualified technician.
The low beam headlight bulbs are high voltage discharge tube bulbs. High voltage can remain in the circuit even with the light switch off and the key removed. Because of this, you should not attempt to examine or change a low beam headlight bulb yourself. If a low beam headlight bulb fails, take the vehicle to your dealer to have it replaced.
462
2010 RL ０９／０４／０２ １９：３８：１１ ３１ＳＪＡ６５０ ０４６８
Remove the left or right side engine compartment cover from the side you are working on by carefully pulling the cover out (see page
451
).
If you are replacing the bulb on the driver’s side, remove the battery cover (see page ). 485
1.
Replacing a Headlight/Daytime Running Light Bulb Your vehicle has halogen high beam headlight bulbs which are also used for the daytime running light. Handle it by its base and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
Lights
BULB
CONNECTOR
2.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
3.
Remove the bulb by turning it one- quarter turn counterclockwise.
CONTINUED
463
2010 RL ０９／０４／０２ １９：３８：２１ ３１ＳＪＡ６５０ ０４６９
Replacing a Front Turn Signal Light Bulb 1.
Remove the left or right side engine compartment cover from the side you are working on by carefully pulling the cover out (see page
451
).
BULB
SOCKET
2.
Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.
3.
Push the bulb in slightly, and turn it counterclockwise.
Lights
4.
5.
Insert the new bulb into the hole, and turn it one-quarter turn clockwise to lock it in place.
Push the electrical connector back onto the bulb. Make sure it is on all the way.
6.
Turn on the headlights to test the new bulb.
7.
Reinstall the engine compartment side cover.
8.
(Driver’s side) Reinstall the battery cover.
464
2010 RL ０９／０４／０２ １９：３８：２９ ３１ＳＪＡ６５０ ０４７０
Lights
4.
Install the new bulb into the socket.
7.
Reinstall the engine compartment side cover.
5.
Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.
6.
Turn on the lights to make sure the new bulb is working.
8.
(Driver’s side) Reinstall the battery cover.
Replacing a Front Parking/Side Marker Bulb 1.
Remove the left or right side engine compartment cover (see page
451
).
2.
(Passenger’s side) Use a flat-tip screwdriver to remove the holding clip from the windshield washer reservoir.
CONTINUED
465
2010 RL ０９／０４／０２ １９：３８：４１ ３１ＳＪＡ６５０ ０４７１
Lights
BULB
SOCKET
CLIP
3.
Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.
5.
Install the new bulb into the socket.
6.
Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.
7.
Turn on the lights to make sure the new bulb is working.
8.
(Passenger’s side) Reinstall the windshield washer reservoir.
Reinstall the engine compartment side cover.
Replacing a Fog Light Bulb Your vehicle uses halogen light bulbs. When replacing a bulb, handle it by its plastic case, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
4.
Pull the bulb straight out of its socket.
9.
(Driver’s side) Reinstall the battery cover.
466
2010 RL ０９／０４／０２ １９：３８：４９ ３１ＳＪＡ６５０ ０４７２
BOLTS
BULB
CLIP
CONNECTOR
1.
Use a Phillips-head screwdriver to remove the two undercover bolts, and remove the holding clip with a flat-tip screwdriver.
3.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
2.
Carefully push up the side under cover into the bumper.
4.
Remove the bulb by turning it one- quarter turn counterclockwise.
Lights
5.
6.
Insert the new bulb into the hole, and turn it one-quarter turn clockwise to lock it in place.
Push the electrical connector back onto the bulb. Make sure it is on all the way.
7.
Turn on the fog lights to test the new bulb.
8.
Reinstall the two undercover bolts on the side under cover and tighten them securely. Put the holding clip back on the side undercover and push on the center until it locks (the center is flush with the head).
467
2010 RL ０９／０４／０２ １９：３８：５９ ３１ＳＪＡ６５０ ０４７３
Lights
Replacing a Rear Turn Signal Light Bulb
BOLTS
BULB
TAIL LIGHT TRIM
3.
Carefully pry in the top or bottom edge of the trim with a small flat- tip screwdriver, and pull the trim straight back.
4.
Remove the two mounting bolts with an 8 mm wrench.
5.
Pull the taillight assembly straight back out of the body.
SOCKET
6.
Remove the socket by turning it one-quarter turn counterclockwise.
7.
Remove the burned out bulb by pulling it straight out of its socket.
MOUNTING NUT
MAINTENANCE LID
1.
Open the trunk lid, and remove the left or right maintenance lid.
2.
Remove the mounting nut with an 8 mm wrench.
468
2010 RL ０９／０４／０２ １９：３９：０９ ３１ＳＪＡ６５０ ０４７４
8.
9.
Install the new bulb in the socket by pushing it straight in the socket until it bottoms.
Reinstall the socket into the light assembly. Turn it clockwise to lock it in place.
10.
Test the lights to make sure the new bulb is working.
11.
When reinstalling the taillight assembly, align and pop the snap fasteners in place. Tighten the two mounting bolts and reinstall the trim in place.
12.
Tighten the mounting nut securely, and reinstall the maintenance lid.
Replacing a Back-up Light Bulb
COVERS
BULB
Lights
1.
Open the trunk.
2.
Remove the light assembly cover by pulling its outside edge.
SOCKET
3.
4.
Remove the socket from the light assembly by turning it one-quarter turn counterclockwise.
Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.
CONTINUED
469
2010 RL ０９／０４／０２ １９：３９：１７ ３１ＳＪＡ６５０ ０４７５
Lights, Dust and Pollen Filter, Cleaning the Seat Belts
5.
Reinstall the socket into the light assembly. Turn it clockwise to lock it in place.
6.
Test the lights to make sure the new bulb is working.
7.
Reinstall the back-up light cover.
Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the climate control system.
Have your dealer replace the filter when this service is indicated by a maintenance message on the multi- information display. It should be replaced every 15,000 miles (24,000
km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the climate control system becomes less than usual.470
Cleaning the Seat Belts
LOOP
If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.
2010 RL ０９／０４／０２ １９：３９：２３ ３１ＳＪＡ６５０ ０４７６
DRIVER’S SIDE FLOOR MAT
If you use a non-Acura floor mat, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats.
Unlock
Lock
ANCHORS
The floor mats that came with your vehicle hook over the floor mat anchors. To lock each anchor, turn the knob clockwise. This keeps the floor mats from sliding forward (possibly interfering with the pedals), or backwards (making the front passenger’s weight sensors ineffective).
If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle.
Floor Mats
REAR PASSENGER’S FLOOR MAT
ANCHOR
Unlock
Lock
Make sure the rear floor mats are properly hooked to the floor mat anchors. Your vehicle is equipped with front passenger’s seat weight sensors. If the rear passenger’s floor mat is on the seat rail of the front passenger’s seat, the sensors will detect the decreased weight on the seat, and they may not work properly.
471
2010 RL ０９／０４／０２ １９：３９：３０ ３１ＳＪＡ６５０ ０４７７
Wiper Blades
Check the condition of the wiper blades at least every 6 months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.
HOLDING LOCATIONS
COVER
WIPER ARMS
BLADE
SCREWS
1.
Adjust the windshield wiper arms to the winter position by holding both wiper arms as shown in the illustration at the same time (see page ). Raise the wiper arms off the windshield.
139
2.
Push the end of the cover on the blade assembly until the other end is pivoted out, and remove the cover.
3.
Disconnect the blade assembly from the wiper arm by removing the two screws from the arm.
Do not open the hood when the wiper arms are raised, or you will damage the hood and the wiper arms.
472
2010 RL ０９／０４／０２ １９：３９：３７ ３１ＳＪＡ６５０ ０４７８
BLADE
BLADE
4.
Remove the blade from its holder by grabbing the tabbed end of the blade. Pull up firmly until the tabs come out of the holder.
REINFORCEMENT
5.
Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.
Wiper Blades
6.
Slide the new wiper blade into the holder until the tabs lock.
7.
8.
Reinstall the blade assembly to the wiper arm and tighten the two screws securely. Reinstall the cover by pushing it in.
Set the wiper arms back on the windshield. Adjust the windshield wipers to their previously parked position.
473
2010 RL ０９／０４／０２ １９：３９：４６ ３１ＳＪＡ６５０ ０４７９
Wheels, Tires
Wheels Clean the wheels as you would the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.
Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.
Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.
Aluminum alloy wheels have a protective clear-coat that keeps the aluminum from corroding and tarnishing. Cleaning the wheels with harsh chemicals (including some commercial wheel cleaners) or a stiff brush can damage the clear-coat. To clean the wheels, use a mild detergent and a soft brush or sponge.
The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.
Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.
Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.
The tire pressure monitoring system (TPMS) will warn you when a tire pressure is low. See page for information on the TPMS.
423
474
2010 RL ０９／０４／０２ １９：３９：５３ ３１ＳＪＡ６５０ ０４８０
Even though your vehicle is equipped with TPMS, we recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.
Use a gauge to measure the air pressure in each tire at least once a month. Even tires that are in good condition may lose one to two psi (10
to 20 kPa, 0.1 to 0.2 kgf/cm ) per month. Remember to check the spare tire at the same time.Check the pressure in the tires when they are cold. This means the vehicle has been parked for at least three hours, or driven less than 1 mile (1.6
km).If you check the pressure when the tires are hot [driven for several miles (kilometers)], you will see readings 4
to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold reading. This is normal; do not release air to match the cold pressure. The tires will be underinflated.You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.
Add or release air, if needed, to match the recommended cold tire pressures on page
476
Tires
While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.
475
2010 RL ０９／０４／０２ １９：４０：０６ ３１ＳＪＡ６５０ ０４８１
For convenience, the recommended tire sizes and cold tire pressures are on a label on the driver’s doorjamb.
For additional technical information about your tires, see page
520
High Speed Driving U.S.modelonly We strongly recommend that you do not drive faster than the posted speed limits and conditions allow. If you ever drive in a sanctioned competitive event at sustained high speeds (over 112 mph or 181 km/h), be sure to adjust the cold tire pressures as shown below. If you do not, excessive heat can build up and cause sudden tire failure.
Tires
Recommended Tire Pressures The following charts show the recommended cold tire pressures for most normal and high-speed driving conditions.
NormalDriving
Tire Size/Type P245/45R18 96V
Cold Tire Pressure
Front
32 psi (220 kPa , 2.2 kgf/cm )
Rear
30 psi (210 kPa , 2.1 kgf/cm ) 60 psi (420 kPa , 4.2 kgf/cm )
Compact Spare T155/70D17
110M
476
HighSpeedDriving
Tire Size
Cold Tire Pressure
P245/45R18 96V
Front
36 psi (250 kPa , 2.5 kgf/cm )
Rear
35 psi (240 kPa , 2.4 kgf/cm )
The recommended tire pressures for high speed driving are not on the label on the driver’s doorjamb, contact your dealer for more information about the tire pressures.
2010 RL ０９／０４／０２ １９：４０：１３ ３１ＳＪＡ６５０ ０４８２
When you return to normal speed driving, be sure to readjust the tire pressure for normal driving. You should wait until the tires are cold before adjusting the tire pressure.
Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear.
You should look for:
Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.
Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.
Excessive tread wear.
Tires
INDICATOR LOCATION MARKS
TREAD WEAR INDICATORS
Your tires have wear indicators molded into the tread. When the tread wears down, you will see a 1/2
inch (12.7 mm) wide band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire.A tire this worn gives very little traction on wet roads. You should replace the tire if you can see three or more tread wear indicators.
477
2010 RL The last four digits of the TIN (tire identification number) are found on the sidewall of the tire and indicate Tire the date of manufacture (See Labeling
on page
522
).
０９／０４／０２ １９：４０：１８ ３１ＳＪＡ６５０ ０４８３
Tires
Tire Service Life The service life of your tires is dependent on many factors, including, but not limited to, driving habits, road conditions, vehicle loading, inflation pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use).
In addition to your regular inspections and inflation pressure maintenance, it is recommended that you have annual inspections performed once the tires reach five years old. It is also recommended that all tires, including the spare, be removed from service after 10 years from the date of manufacture, regardless of their condition or state of wear.
478
2010 RL ０９／０４／０２ １９：４０：２８ ３１ＳＪＡ６５０ ０４８４
Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.
Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.
Improper wheel weights can damage your vehicle’s aluminum wheels. Use only Acura wheel weights f or balancing.
Tire Rotation
Front
Front
(For Non-directional Tires and Wheels)
(For Directional Tires and Wheels)
To help increase tire life and distribute wear more evenly, rotate the tires according to the maintenance messages displayed on the multi-information display. Move the tires to the positions shown in the illustration each time they are rotated. If you purchase directional tires, rotate only front-to-back.
When the tires are rotated, make sure the air pressures are checked.
Tires
Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).
Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS and vehicle stability assist system (VSA) to work inconsistently.
The ABS and VSA system work by comparing the speed of each wheel. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to activate.
CONTINUED
479
2010 RL ０９／０４／０２ １９：４０：３５ ３１ＳＪＡ６５０ ０４８５
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in this owner’s manual.
Tires
It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.
Also be sure you use only TPMS specific wheels. If you do not, the tire pressure monitoring system will not work on that tire.
If you ever need to replace a wheel, make sure the wheel’s specifications match those of the original wheel that came on your vehicle. Replacement wheels are available at your Acura dealer.
480
Wheels and Tires Wheels:
18 x 8.0J AL (TPMS)
Tires:
P245/45R18 96V
520
for DOT tire quality
See page grading information, and page for tire size explanation. 522
2010 RL ０９／０４／０２ １９：４０：４２ ３１ＳＪＡ６５０ ０４８６
Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.
＋
For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.
SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.
Tires
TireChains Mount tire chains on your tires when required by driving conditions or local laws. Install them only on the front tires.
Because your vehicle has limited tire clearance, Acura strongly recommends using the chain listed below, made by Security Chain Company (SCC).
Cable-type: SCC Radial Chain SC1042
CONTINUED
481
2010 RL ０９／０４／０２ １９：４０：４６ ３１ＳＪＡ６５０ ０４８７
Tires
When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.
Follow all instructions in this owner’s manual regarding the selection and use of tire chains.
Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.
482
2010 RL ０９／０４／０２ １９：４０：５４ ３１ＳＪＡ６５０ ０４８８
Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion.
If additional battery maintenance is needed, see your dealer or a qualified technician.
Battery posts,
WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.
Checking the Battery
If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.
) cable first, and
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.
Wear protective clothing and a face shield, or have a skilled technician do the battery maintenance.
CONTINUED
483
TEST INDICATOR WINDOW
Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors. To see the label, remove the battery cover (see page
485
).
2010 RL ０９／０４／０２ １９：４１：０１ ３１ＳＪＡ６５０ ０４８９
Onvehicleswithoutnavigationsystem The compass system will also disable itself. The next time you turn on the ignition switch, the system will require you to enter a PIN before it can be used. Enter the four-digit anti- theft security code (see page ). You will also need to reset the clock according to the instruction of 313
setting the clock (see page298
).
Checking the Battery
If your vehicle’s battery is disconnected or goes dead, all stored driving positions will be lost. To store the driving positions again, see the storing procedure on page
163
Onvehicleswithnavigationsystem The navigation system will also disable itself. The next time you turn on the ignition switch, the system will require you to enter a PIN before it can be used. Refer to the navigation system manual.
484
If your vehicle’s battery is disconnected or goes dead, the audio system may disable itself. The next time you turn on the radio you will see ‘‘ display. Use the preset buttons to enter the code (see page
’’ in the frequency
280
).
If your vehicle’s battery is disconnected or goes dead, the power tilt and telescopic steering wheel system will be disabled. The system needs to be reset after reconnecting the battery (see page 149
).
2010 RL ０９／０４／０２ １９：４１：０９ ３１ＳＪＡ６５０ ０４９０
