POSITION SETUP
see page 107
LIGHTING SETUP
see page 110
DOOR/WINDOW
SETUP
see page 115
WIPER SETUP
see page 123
CONTINUED
95
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Adaptive Cruise Control Setup Ifequipped There are two custom settings for adaptive cruise control (ACC): â— PRE-RUNNING CAR DETECT
BEEP
◠ACC DISPLAY SPEED UNIT To enter customize mode, press the SEL/RESET button while ‘‘ACC SETUP’’ is displayed. Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
SEL/RESET BUTTON INFO (â–²/â–¼) BUTTON
96
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Pre-RunningCarDetectBeep
Multi-Information Display
Press the SEL/RESET button to display the selections. Select ON or OFF by pressing the INFO ( / ) button, then press the SEL/RESET button to enter your selection.
When your selection is successfully completed, the display changes as shown above, and then returns to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, return to ‘‘PRE- RUNNING CAR DETECT BEEP’’ and repeat the procedure again.
When PRE-RUNNING CAR DETECT BEEP is set to ON, one beep sounds when the ACC detects a vehicle in front of you. A beep also sounds when that vehicle passes out of the range of your vehicle's radar sensor. Select this item from ‘‘ACC SETUP’’ by pressing the INFO ( / ) button repeatedly until ‘‘PRE-RUNNING CAR DETECT BEEP’’ is displayed.
CONTINUED
97
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
AdaptiveCruise ControlDisplaySpeedUnit
To change the unit of measurement from mph to km/h, follow these instructions: Select this item from ‘‘ACC SETUP’’ by pressing the INFO ( / ) button repeatedly until ‘‘ACC DISPLAY SPEED UNIT’’ is displayed.
98
Press the SEL/RESET button to display the selections. The highlighted unit, mph or km/h, is the current setting. To change the setting, press the INFO ( / ) button until the unit you want is highlighted, then press the SEL/ RESET button.
When your selection is successfully completed, the display changes as shown above, and then returns to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, return to ‘‘ACC DISPLAY SPEED UNIT’’ and repeat the procedure again.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Meter Setup Here are the six custom settings for the meter setup: â— LANGUAGE SELECTION â— ADJUST OUTSIDE TEMP.
DISPLAY
â— TRIP A & AVG. FUEL RESET with
REFUEL
â— ADJUST ALARM VOLUME â— ELAPSED TIME RESET â— AUTO INTERIOR ILLUMINATION
While METER SETUP is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
Multi-Information Display
CONTINUED
99
SEL/RESET BUTTON INFO (â–²/â–¼) BUTTON
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
LanguageSelection
There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions: You can choose this customizable item from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired language by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘LANGUAGE SELECTION’’ and repeat the procedure again.
100
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
AdjustOutsideTemp.Display
U.S. models
U.S. models
Multi-Information Display
Canadian models
Canadian models
If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions: You can choose this customizable item from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
Adjust the outside temperature value by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to set the desired value.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again.
CONTINUED
101
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
TripA&Avg.FuelResetWithRefuel
To cause Trip A and AVG. FUEL to reset every time you refuel your vehicle, follow these instructions: You can choose this customizable item from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP A & AVG. FUEL RESET with REFUEL’’ and repeat the procedure again.
102
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
AdjustAlarmVolume
Multi-Information Display
Select the warning alarm volume from three levels. You can choose this customizable item from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired level by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST ALARM VOLUME’’ and repeat the procedure again.
CONTINUED
103
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
ElapsedTimeReset There are four elapsed time reset choices you can make: MANUAL ONLY ï¼ You can reset the elapsed time, when Trip Computer's Elapsed Time is displayed (see page 85). IGN OFF ï¼ The elapsed time is reset when you turn the ignition switch to the LOCK (0) position. TRIP A ï¼ The elapsed time is reset when the Trip A is reset. TRIP B ï¼ The elapsed time is reset when the Trip B is reset.
104
You can choose this customizable item from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
You can choose this customizable item from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
AutoInteriorIllumination While the headlight switch is turned on, the interior lights gradually dim, as the outside light level gets low. You can customize at which outside light level the lights start to dim. There are MAX, HIGH, MID, LOW and MIN levels and OFF for the auto interior illumination settings. If you want the illuminations to start dimming as early as possible, select MAX. For illuminations to start dimming as late as possible, select MIN. Choose HIGH, MID, or LOW for levels in between. To disable the auto interior illumination function, select OFF.
CONTINUED
105
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO INTERIOR ILLUMINATION’’ and repeat the procedure again.
106
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Position Setup Here are the two custom settings for the position setup: â— MEMORY POSITION LINK â— AUTO TILT & TELESCOPE
STEERING WHEEL
While ‘‘POSITION SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO ( / ) button, the screen changes as shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
SEL/RESET BUTTON
INFO (â–²orâ–¼) BUTTON
CONTINUED
107
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
MemoryPositionLink
If ‘‘MEMORY POSITION LINK’’ is set to ‘‘ON,’’ the driver's seat, the steering wheel, and outside mirror positions move to the position stored in the memory when you open the driver's door, using the remote transmitter. You can choose this customizable item from ‘‘POSITION SETUP’’ by pressing the INFO ( / ) button repeatedly.
108
Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘MEMORY POSITION LINK’’ and repeat the procedure again.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
AutoTilt&TelescopeSteeringWheel
Multi-Information Display
When ‘‘AUTO TILT & TELESCOPE STEERING WHEEL’’ is set to ‘‘ON,’’ the steering wheel automatically moves fully in and up when you turn the ignition switch to the LOCK (0) position and remove the key. You can choose this customizable item from ‘‘POSITION SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO TILT & TELESCOPE STEERING WHEEL’’ and repeat the procedure again.
CONTINUED
109
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Lighting Setup Here are the three custom settings for the lighting setup: â— INTERIOR LIGHT DIMMING
TIME
◠HEADLIGHT AUTO OFF TIMER ◠AUTO LIGHT SENSITIVITY While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO ( / ) button, the screen changes as shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
110
SEL/RESET BUTTON INFO (â–²orâ–¼) BUTTON
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
InteriorLightDimmingTime
Multi-Information Display
The interior lights fade out when you close all doors and tailgate. To change how long the lights stay on before they fade out, follow these instructions: You can choose this customizable item from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again.
CONTINUED
111
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
HeadlightAutoOffTimer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you remove the key from the ignition switch and close the driver's door. To change how long the lights stay on before they go off, follow these instructions:
112
You can choose this customizable item from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
AutoLightSensitivity The headlights automatically come on when the headlight switch is in the AUTO position and the ambient light reaches a changeable level. You can select the auto light sensitivity from the following five levels: MAX ï¼ The headlights come on when it is bright. HIGHï¼ The headlights come on when it is somewhat bright. MIDï¼ The headlights come on when it is as bright as sunset or sunrise. LOWï¼ The headlights come on when it is somewhat dark. MINï¼ The headlights come on when it is dark.
Multi-Information Display
You can choose this customizable item from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ) button repeatedly.
CONTINUED
113
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘HEADLIGHT AUTO OFF TIMER’’ and repeat the procedure again.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO LIGHT SENSITIVITY’’ and repeat the procedure again.
114
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Door/Window Setup Here are the five custom settings for the door/window setup: â— AUTO DOOR LOCK â— AUTO DOOR UNLOCK â— KEY AND REMOTE UNLOCK
MODE
â— KEYLESS LOCK
ACKNOWLEDGMENT
◠SECURITY RELOCK TIMER While ‘‘DOOR/WINDOW SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO ( / ) button, the screen changes as shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
SEL/RESET BUTTON INFO (â–²orâ–¼) BUTTON
CONTINUED
115
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
AutoDoorLock There are three settings you can choose from: SHIFT FROM Pï¼ The doors lock whenever you move the shift lever out of Park. WITH VEH SPD ï¼ The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h). OFFï¼ The auto door lock is deactivated all the time.
116
You can choose this customizable item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( /
) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
You can choose this customizable item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( /
) button repeatedly.
AutoDoorUnlock There are three settings you can choose from: SHIFT TO Pï¼The driver's door or all the doors, depending on the door lock mode setting (see page 116), unlock when you move the shift lever to Park with the brake pedal depressed. IGN OFFï¼The driver's door or all the doors, depending on the door lock mode setting (see page 116), unlock when you turn the ignition switch to the LOCK (0) position. OFFï¼ The auto door unlock is deactivated all the time. This is the factory default setting.
CONTINUED
117
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
If you choose ‘‘SHIFT TO P’’ or ‘‘IGN OFF’’, you will see the above display. Press the INFO ( / ) button to switch the door lock mode setting between the driver's door and all doors. Then, press the SEL/RESET button to enter your selection.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.
118
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
KeyandRemoteUnlockMode
Multi-Information Display
To select whether the driver's or all doors unlock when the remote transmitter or key is used, follow these instructions. You can choose this customizable item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( /
) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEY AND REMOTE UNLOCK MODE’’ and repeat the procedure again.
CONTINUED
119
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the tailgate are locked and the security system has set (see page 341). You can customize the exterior lights not to flash and the beeper not to sound.
120
You can choose this customizable item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( /
) button repeatedly.
Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
SecurityRelockTimer If you unlock the doors and the tailgate with the remote transmitter, but do not open any of the doors or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system sets. You can change this relock time from 30 seconds to 60 or 90 seconds.
Multi-Information Display
You can choose this customizale item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.
CONTINUED
121
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.
122
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Wiper Setup
SEL/RESET BUTTON INFO (â–²/â–¼) BUTTON
Here is one custom setting for the wiper setup: ◠WIPER ACTION While ‘‘WIPER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
Multi-Information Display
WiperAction You can select from these two settings when the wiper switch is in the INT (intermittent) position: INTERMITTENT ï¼ The intermittent operation varies according to the selection you make on the wiper lever's intermittent control ring. WITH VEH SPDï¼The intermittent operation varies according to vehicle speed.
CONTINUED
123
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Multi-Information Display
You can choose this customizable item from ‘‘WIPER SETUP’’ by pressing the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘WIPER ACTION’’ and repeat the procedure again.
124
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Controls Near the Steering Wheel
HEADLIGHT/TURN SIGNAL/ FRONT FOG LIGHTS (P. 128)
PADDLE SHIFTERS (P. 447)
WINDSHIELD WIPERS/WASHERS (P. 126)
BSI ALERT INDICATORᤳ1
(P. 479)
ᤳ4
COLLISION MITIGATION
BRAKING SYSTEMâ„¢ (CMBSâ„¢)
OFF BUTTONᤳ1 (P. 467)
MIRROR CONTROLS
(P. 166)
VEHICLE STABILITY
ASSIST SYSTEM OFF
BUTTON (P. 474)
BLIND SPOT
INFORMATION SYSTEM
(BSI) OFF BUTTONᤳ1
(P. 482)
HEADLIGHT WASHER
BUTTONᤳ1 (P. 127)
STEERING WHEEL AUDIO CONTROLS (P. 305) STEERING WHEEL ADJUSTMENTS (P. 134)
HORNᤳ2
VOICE CONTROL
BUTTONSᤳ3
DISTANCE
BUTTONᤳ1
(P. 357)
BLUETOOTH HANDSFREELINK BUTTON (P. 365)
CRUISE CONTROL BUTTONS (P. 345)/ ADAPTIVE CRUISE CONTROL (ACC) BUTTONSᤳ1 (P. 353)
ᤳ 1: If equipped ᤳ 2: To use the horn, press the center pad of the steering wheel. ᤳ 3: Refer to the navigation system manual. For how to operate Bluetooth®HandsFreeLink by voice, see page 383. ᤳ 4: Switch location varies on models.
125
INSTRUMENT PANEL BRIGHTNESS (P. 133) PASSENGER AIRBAG OFF INDICATOR (P. 37) HAZARD WARNING BUTTON (P. 132) REAR WINDOW DEFOGGER (P. 132) ACCESSORY POWER SOCKETS (P. 177)
SEAT HEATER SWITCHES
(P. 157)/
SEAT HEATER AND SEAT
VENTILATION BUTTONSᤳ1
(P. 158)
ACTIVE DAMPER
SYSTEM BUTTONᤳ1
(P. 484)
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Windshield Wipers and Washers
Push the right lever up or down to select a position. MIST ï¼ The wipers run at high speed until you release the lever. OFF ï¼ The wipers are not activated. INT ï¼ The length of the wipe interval is varied automatically according to vehicle speed. Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h). To change the ‘‘WIPER ACTION’’ setting, see page 123.
position), the
LO ï¼ The wipers run at low speed. HI ï¼ The wipers run at high speed. Windshield Washer ï¼ Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever. When you activate the windshield washer with the headlights turned on, the headlight washer will be activated under certain conditions. For more information, see following HeadlightWasherssection.
1. MIST 2. OFF 3. INT ï¼ Intermittent 4. LO ï¼ Low speed 5. HI ï¼ High speed 6. Windshield washers
126
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
HeadlightWashers (OnCanadianmodels)
MDX model
Technology Package and Elite Package models
Rear Window Wiper and Washer
Windshield Wipers and Washers
The headlight washers use the same fluid reservoir as the windshield washers.
1. Rotate the switch clockwise to turn
the rear window wiper ON.
2. Hold past ON to turn the rear
window wiper on and to spray the rear window washer.
The headlight washers can be operated at any time by pressing the headlight washer button located next to the steering wheel column. The headlights must be turned on to use this button. In addition, the headlight washer operates without pressing the button the first time you turn on the windshield washers with the ignition switch in the ON (II) position.
CONTINUED
127
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Windshield Wipers and Washers, Turn Signal and Headlights
3. When you turn the wiper switch to the ‘‘OFF’’ position, the wiper will return to its parked position.
4. Rotate the switch
counterclockwise to spray the window washer. When you shift the transmission to the reverse position with the front windshield wipers activated, the rear window wiper operates automatically. When the wiper control lever position is INT, the rear wiper operates intermittently. When it is LO or HI, the rear wiper operates continuously.
The rear window washer uses the same fluid reservoir as the windshield washer.
128
Turn Signal and Headlights
1. Turn signal 2. Off 3. Parking and indicator lights 4. AUTO 5. Headlights on 6. High beams 7. Flash high beams 8. Fog lights off 9. Fog lights on
Turn Signal ï¼ Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn. Headlights On ï¼ Turning the switch to the ‘‘ the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the ‘‘ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver's door.
’’ position turns on
’’
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
When the light switch is in either of these positions, the lights on indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position. High Beams ï¼ To switch from low beams to high beams, push the left lever forward until you hear a click. The blue high beam indicator will come on (see page 74). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams stay on as long as you hold the lever back.
AUTO ï¼ The automatic lighting feature turns on the headlights and all other exterior lights, when it senses low ambient light. To turn on automatic lighting, turn the light switch to AUTO at any time. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light. The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver's door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the
position.
Turn Signal and Headlights
Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities. To change the ‘‘AUTO LIGHT SENSITIVITY’’ setting, see page 113. Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.
CONTINUED
129
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Fog Lights Turn the fog lights on and off by turning the switch next to the headlight switch. You can use the fog lights only when the headlights are on low beam. With the light switch in the AUTO position, you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off.
Daytime Running Lights With the headlight switch off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake. When the headlights are on, the daytime running lights are off.
Turn Signal and Headlights
LIGHT SENSOR
The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.
130
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi-information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked. When the multi-information display shows a ‘‘DRL OFF’’ message, the daytime running lights are off. Follow the procedure in the left column to turn them on.
Automatic Lighting Off Feature
This feature turns off the headlights,
all other exterior lights, and the
instrument panel lights within 15
seconds after you remove the key
and close the driver's door.
To change the ‘‘HEADLIGHT AUTO
OFF TIMER’’ setting, see page 112.
The automatic lighting off feature
activates if you leave the headlight
switch in the ‘‘
position or if the lights are turned on
by setting the switch in the ‘‘AUTO’’
position, and you remove the key,
then open and close the driver's
door.
’’ or ‘‘
’’
Turn Signal and Headlights
If you turn the ignition switch to the
LOCK (0) position with the headlight
switch on, but do not open the door
the lights turn off after 10 minutes (3
minutes, if the switch is in the
‘‘AUTO’’ position).
The lights turn on again when you
unlock or open the driver's door. If
you unlock the door, but do not
open it within 15 seconds, the
lights go off. With the driver's
door open, you will hear a lights-
on reminder chime.
131
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Hazard Warning Button, Rear Window Defogger
Hazard Warning Button
Rear Window Defogger
Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the vehicle.
132
Make sure the rear window is clear and you have good visibility before starting to drive. The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side. Pushing this button also turns the mirror heaters on or off. For more information, see page 167.
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Adjust the brightness of the instrument panel by pressing the + or ï¼ button. Press the + button to increase the brightness and the ï¼ button to decrease it. The brightness can be set differently for when the headlights are on, and when they are off.
The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.
Instrument Panel Brightness
. To cancel the glare reduction
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to or function, set the brightness to the highest level, then press the + button. You will hear a beep when it is canceled. You can customize when the glare reduction function starts. To change ‘‘AUTO INTERIOR ILLUMINATION’’, see page 105 for more information.
133
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
Steering Wheel Adjustments
Make any steering wheel adjustment before you start driving.
ADJUSTMENT SWITCH
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
Move the steering wheel in, out, up, or down by pushing and holding the adjustment switch in that direction.
Release the switch when the steering wheel reaches the desired position. Make sure the steering wheel points towards your chest, not toward your face, and that you can see the instrument panel gauges and indicators.
134
2013 MDX12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu
When you remove the key from the ignition switch, the steering wheel automatically moves fully in and up. To change the ‘‘AUTO TILT & TELESCOPE STEERING WHEEL’’ setting, see page 109. The steering wheel then returns to its original position when you insert the key back in the ignition switch. Steering wheel movement is also controlled by the driving position memory system (see page 168).
If your vehicle's battery is disconnected or goes dead, or the fuse for the power tilt and telescopic steering wheel is removed, the power tilt and telescopic steering wheel system needs to be reset when you reconnect the battery or install the fuse. Insert the key into the ignition switch, and remove it. The steering wheel automatically moves fully in and up to let you know the system is reset.
Steering Wheel Adjustments