Login
21st October 2012 - 02:17 PM
 |
S2krazie
Post #1963
Yesterday I went down the Coast picked up my parts, tail lights and CD player. Came home from work today and installed one of the tails. Glad Ibought a set because the tint colour is slightly off. WHat a funk around it is to remove tail lights from an NSX. Yet another stupid Honda design. |
|---|
|
|
S2krazie
Post #1965
Replaced the 2 tail lights, with the 2nd hand Yahoo acutions JDM ones that dont fog up, $1000 later.... LOL. |
|---|
 |
|---|
 |
|---|
 |
the_random_hero
Post #1970
Another 6-8 weeks to get the CORRECT brake pads for my car. It's never ending |
|---|
 |
RB25_lovin
Post #1972
QUOTE (DAL32 @ Oct 18 2012, 07:48 AM)   Got trolled by Rays Engineering. I spent money on hub adapters and damaged the threads on one of them trying to fit the wheels up only to discover I could have probably fitted them without! Oh well, ordered correct hub rings and will soon be putting wheels on car have u put the wheels on yet? |
|---|
 |
DAL32
Post #1974
QUOTE (RB25_lovin @ Oct 30 2012, 05:51 PM) have u put the wheels on yet? I did, on the rear tonight at least:  I found another broken valve and managed to get 38psi into it last night but it wouldn't read on my gauge tonight and felt a bit flat so I have to now wait until the weekend. Joy. Until then, I am all ready for Johno Rd skids. Coz FWD Can't wait to get some coilovers for this bitch. It was going to be now, but my car funked me with a major service last week which was to the value of coilovers. |
|---|
|
|
35NIK
Post #1976
QUOTE (j.d.m @ Nov 4 2012, 12:03 PM) Pulled out my old shitty dvd player and found this...  After cutting the fibre-glass tape holding it together and a sh!t electrical tape wrapping job  Managed to get it like this  Installed.  You think that wiring is bad... Wait until I can find my Is200 wiring harness, as I pulled out the headunit, the loom fell apart in my hands. lol |
|---|
|
|
RB25_lovin
Post #1977
QUOTE (DAL32 @ Oct 31 2012, 10:07 PM) I did, on the rear tonight at least: I found another broken valve and managed to get 38psi into it last night but it wouldn't read on my gauge tonight and felt a bit flat so I have to now wait until the weekend. Joy. Until then, I am all ready for Johno Rd skids. Coz FWD Can't wait to get some coilovers for this bitch. It was going to be now, but my car funked me with a major service last week which was to the value of coilovers. its gunna look sick when that gap is gone |
|---|
 |
|---|
 |
patrick_h_oz
Post #1981
After several abortive attempts with Inox, hammers of increasing weights and breaking a tie rod remover I bit the bullet and bought a whole knuckle and hub assembly. I now have new tie-rod and rack end fitted.. finally! Now to do the rack end on the other side, but that shouldn't take too long, fingers crossed. |
|---|
 |
bandit_corolla
Post #1982
Ran 8mm copper fuel line from tank to the front. Its posted in the general section. |
|---|
|
|
RB25_lovin
Post #1990
QUOTE (Aarie @ Aug 4 2012, 04:20 PM) Tried to funk around with my flash tuner to get it to shift softer (looses traction in 3rd at 120km/h) Had no luck because the moron I baught it off fuched up all the factory settings. lol  hey aerie 
|
|---|
|
|
stockmy00
Post #1991
Rear coils are on now, spent yesterday afternoon/night doing them over a few beers with mates. So glad I put them on, only been round like 2 corners at reasonable pace and can feel the potential! They aren't as comfortable as the stock struts were but they are only mildly rougher and will handle 10 times better so very worth it. |
|---|
 |
|---|
-
Member Login
If you have a BoostCruising account enter your user name and password into the yellow box.
Alternatively, you can quickly login with Facebook.
If you don't have an account create one below.
Create Account -
Login using your Facebook account!