Back

 "Shootin' The Breeze" - Old Skool Chat Thread  

Page 29 of 107
Jump to page
Post Topic
jebby88
Post #981

thanks for the info, Just had a look at my step dads wb tonner and he can fit 6x9s behind the seats. So ill be putting 6" in the kickpanels and 6x9s behind the seats. Would the 6x9s need individual boxes or will they be fine just sitting there?

wbtonner
Post #982

They would need individual boxes.
Buy a pair of small 6x9 box.
Take EVERYTHING out of the car, seats, carpet, underlay etc.
Get some plastic sheeting and loosly cover the area where the box will fit behind each seat. (Also make sure the bare metal is clean)
Get some fibre glass and some resin. Glass the area up. 3 thick sheets with a decent resin will be fine. (Will pull out when cured and plastic will peel off)
Cut box to sit snuggly against fibre glass.
Epoxy glue box to fibre glass. Re carpet rear wall but not the floor. Glue boxes into place, or screw/bolt. fold carpet over the box. Cut a hole out where the speak goes, screw the speaker into the box and it will hold the carpet in place.


Also, I run a 6x9 in each of my kick panels. Works fine, doesn't hit on the pedals, and is loud enough off the headunit. I'd recommend using dynamat behind the kick panels.


QUESTION: You want a custom interior yet you don't want any speakers to be seen. My head is full of fuck. Also, I don't know how tall you are, but don't put the amp (if you want to run one) behind the drivers seat as it will put he seat that much more forward. (I have my seat as far back as possible).

DeadSled
Post #983

How do you know how well your speakers sound Nathan when last i saw they don't work tongue.gif

jebby88
Post #984

Im about 6 "2.
im getting some vinyl racing buckets to replace the premier seats as they will give me the leg room i need and they will be the same colour my interior will be trimmed in (black). It depends on the price the custom interior will cost, if its too much i will just go stock. The cards will be clean with only the window winders and door handle visible. The hardest thing is replacing the dash pad, i have looked around and to get a new replacement im looking at about $500 so i think ill just have to find a decent second hand one and paint it if necessary. My old mans driving the hj around as he has sold his car so it will most likely be slow project.

Thanks for the advice

boost bogan
Post #985

6" in the kicks will give you no staging unless you run components (separate tweeter) 6x9's behind seats sound shit and muffled no matter which way you install them but easiest way is to use the holes at the bottom of the rear firewall in kingswood utes. Mount an mdf board along the bottom of the holes to cover them up (10-12mm mdf) and mount the 6x9's in there.

P.S unless he is 3ft . 5" you will not fit a slimline sub behind the seats thumbsup.gif

wbtonner
Post #986

QUOTE (boost bogan @ Apr 18 2011, 05:50 PM) *
6" in the kicks will give you no staging unless you run components (separate tweeter) 6x9's behind seats sound shit and muffled no matter which way you install them but easiest way is to use the holes at the bottom of the rear firewall in kingswood utes. Mount an mdf board along the bottom of the holes to cover them up (10-12mm mdf) and mount the 6x9's in there.

P.S unless he is 3ft . 5" you will not fit a slimline sub behind the seats thumbsup.gif

Debatable, I have a 10" slimline that I was going to mount behind the drivers seat. However, would sound super shit as the box would have very little air space.

wbtonner
Post #987

Could always do this Jebby?
jebby88
Post #988

QUOTE (wbtonner @ Apr 18 2011, 07:07 PM) *
Could always do this Jebby?

woah that's different, i have to admit it would be pretty sick with the subs in that location. It would be really loud especially in a ute. I don't like seeing the monoblock/amp but you allways put it on the outside of the rear firewall

Monaro454
Post #989

just put my weld draglites on ebay last night..... sold them tonight!! must have put them on too cheap, $1250.00
now I just have the HQ roller and the 9 inch to sell.... any takers?

jebby88
Post #990

QUOTE (wbtonner @ Apr 17 2011, 09:41 PM) *
Doing what you crazy mofo's do tomorrow, and until I buy another daily, drive my ute to work. 100km round trip. Will fill her up tomorrow morning then again on Tuesday morning to see how much it cost me, not looking forward to the amount haha.
My guess $33.50 haha.

You sold the tonner?
wbtonner
Post #991

No lol, my laser.

HSV
Post #992

QUOTE (Monaro454 @ Apr 18 2011, 08:24 PM) *
just put my weld draglites on ebay last night..... sold them tonight!! must have put them on too cheap, $1250.00
now I just have the HQ roller and the 9 inch to sell.... any takers?


Damn I thought they went with the coupe?

$1250 was a good price.

Monaro454
Post #993

too cheap I reckon, they went within 24hrs... I sold them with a pair of half tread MT ET street radials too.

takes me closer to what I wanted for the coupe in the first place!!

-Jordan-
Post #994

Vinyl has been ordered! cool.gif

And borrowing a mates plasma cutter to cut some body work up! oopsie.gif


QUOTE (Monaro454 @ Apr 19 2011, 06:26 AM) *
too cheap I reckon, they went within 24hrs... I sold them with a pair of half tread MT ET street radials too.

takes me closer to what I wanted for the coupe in the first place!!


Sucks to see the car has gone to a new home so far away, but as long as it's what you wanted. Only saw it the once at that formal, but it was amazing! thumbsup.gif

Anchor
Post #995

How much for the 9" and whats it got?
Monaro454
Post #996

QUOTE (Anchor @ Apr 20 2011, 10:03 PM) *
How much for the 9" and whats it got?


probs not enough for you and yours anchor, yours seems pretty serious...

about 3.0 gears, 2 new (never used) HQ pattern 28 spline axles, set up for HQ ute:

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...=STRK:MESELX:IT

have had quite a deal of interest, will probs be sold before midday tomorrow I think.

anybody want an HQ sedan roller?

Monaro454
Post #997

diff sold, sedan sold. see yas.

HSV
Post #998

QUOTE (Monaro454 @ Apr 21 2011, 08:35 PM) *
diff sold, sedan sold. see yas.


Excellent news man biggrin.gif

jebby88
Post

QUOTE (Monaro454 @ Apr 21 2011, 08:35 PM) *
diff sold, sedan sold. see yas.

sad.gif

eh-buddy
Post #1000

well i finaly got a start on my eh this week. found a bit off rust in the rear in the wheel well so i may as well fit some mini tubs but at least it should be a tad fatter with 10's under the ass

ooh anyone got a pair off 15x10 centerlines or welds 4.5" back space to suit hq pattern cheap

HSV
Post #1001

QUOTE (eh-buddy @ Apr 21 2011, 10:02 PM) *
well i finaly got a start on my eh this week. found a bit off rust in the rear in the wheel well so i may as well fit some mini tubs but at least it should be a tad fatter with 10's under the ass

ooh anyone got a pair off 15x10 centerlines or welds 4.5" back space to suit hq pattern cheap


Good luck with that lol.

I saw a set of 12's somewhere in my travels on the intraweb last night cheap.......
eh-buddy
Post #1002

i wish i could fit them theres only enough room for 10'5 with mini tubs i wish i could go full four link though

Monaro454
Post #1003

just sold a set of 15x10 and 15x3.5's Weld Draglites with tyres, wheelnuts and crentrecaps and threw in a set of used MT ET street radials for 1250.00

HSV
Post #1004

Pretty awesome clip, keep an eye on the flat black Camaro in the far lane..........
-Jordan-
Post #1005

QUOTE (HSV @ Apr 22 2011, 06:17 PM) *
Pretty awesome clip, keep an eye on the flat black Camaro in the far lane..........



My face literally went like this ---> eek3.gif to this ---> ohmy.gif to this ---> pray.gif

It's obviously a sign of things to come for me, did the first panel today...
GTRVspec95
Post #1006

QUOTE (Monaro454 @ Apr 22 2011, 06:15 PM) *
just sold a set of 15x10 and 15x3.5's Weld Draglites with tyres, wheelnuts and crentrecaps and threw in a set of used MT ET street radials for 1250.00


I thought I heard Benno sobbing somewhere in the corner ...

QUOTE (-Jordan- @ Apr 22 2011, 07:25 PM) *
It's obviously a sign of things to come for me, did the first panel today...



Mmmmm ... fresh metal

wbtonner
Post #1007

Just thought i'd leave this here. thumbsup.gif



Now show me a late model import that can do this tongue.gif

74QEE
Post #1008

need widened steelies..help meeeee

Monaro454
Post #1009

had some GTS ones... just offloaded them with the Monaro

clutch-monkey
Post #1010

QUOTE (74QEE @ Apr 25 2011, 01:00 PM) *
need widened steelies..help meeeee

is getting some stocko's widened yourself out of the question? (i have no idea what it costs)

74QEE
Post #1011

from what ive heard its a couple of hundred dollars a rim..and when the occasional set pop up on ebay for around the cost of widening one wheel.and who knows..someone on here may have some.there pretty common.

clutch-monkey
Post #1012

QUOTE (74QEE @ Apr 25 2011, 04:49 PM) *
from what ive heard its a couple of hundred dollars a rim..

oh fuck that lol, yeah i'd be trawling swap meets and ebay too

HSV
Post #1013

Got a guy coming down from Mt Isa on thursday to have a look at the Monaro as a rolling shell..........

Aaron-bravo
Post #1014

I did see a set but buggers me where could be gumtree or eBay but yeh sorry doesn't really help

no more holdens
Post #1015

Wide stock rims where like aaaaaarrsholes years ago
Everyone had them
Post wanted add in the classifieds n stuff
They are out there
Ive a set of 13" widies (pair) i cant get $40 for them
So i certainly wouldnt pay alot for them

  • Member Login

    If you have a BoostCruising account enter your user name and password into the yellow box.

    Alternatively, you can quickly login with Facebook.

    If you don't have an account create one below.

    Create Account
  • Forgotten your password?
  • Login with Facebook

    Login using your Facebook account!

Page 29 of 107
Jump to page
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
Loading...
x