Back

 Hyundai Excel Racing Series - Track Attack - Evil things are about to happen to Hyundai Excels  

Page 30 of 53
Jump to page
Post Topic
PRO050
Post #1016

QUOTE (benno.h @ Apr 26 2010, 02:26 PM) *
How many cages have you done now Paul?

I think it's 6 half cages and 2 full cages for the excel guys, and add one more for my little excel that I'll do next week.

Beannie
Post #1017

paul, are you making cages for the excels? (sorry if i didnt see a previous post)
can you pm me some prices?? :o because i want to keep the car road rego'd - i think 6point are illegal on the road? (correct me if im wrong?)
so i'd be interested in something like a 4point fixed or bolt in, but also can bolt up to 6point (if thats legal for road and for the circuit racing series)...

Beannie
Post #1018

i received my camber bolts today, fitted them to top strut bolt, also elongated the top bolt hole to acheive some more camber (dunno if this is ideal or not), and left bottom bolt as standard. adjusted the toe in as it was pretty bad and all done! i think i have about 3-3.5deg neg camber. took it for a drive - makes a noticeable difference :o

looks good - but still have stock springs in it :D might have to look at this issue too

slow bus
Post #1019

With camber bolts top and bottom I have about 4.6

trackattack
Post #1020

Camber will help cornering heaps.
I also have caster kits (bushes) available as well now.

Beannie
Post #1021

just out of curiosity, will lowering the car make more neg camber with the suspension setups excels use? i would assume it would.. by a little bit yeah?

NISMOgemini
Post #1022

on the front it will.. not sure what kind of rear suspension they have.. if its axel beam then it wont on the rear

clutch-monkey
Post #1023

are we going to see any of these excels down at superlap :o

slow bus
Post #1024

QUOTE (trackattack @ Apr 27 2010, 08:21 PM) *
Camber will help cornering heaps.
I also have caster kits (bushes) available as well now.


100% agree no point in running camber if you dont have the caster as well. I have poly offset bushes already.

New struts should arrive in the next couple of days, so should be good for May, although the outside of the car is still a mess.

I will be running monroe fronts and kyb rears, lovell rear springs and unknown front springs.

trackattack
Post #1025

Its good to see a few guys getting the handling side of things sorted.
The softer tyres have likely been suffering wear issues due to the road setup that a lot of people started with.
We might find that we can make a grippy tyre last a lot longer than they have been.

benno.h
Post #1026

QUOTE (trackattack @ Apr 28 2010, 09:59 AM) *
Its good to see a few guys getting the handling side of things sorted.
The softer tyres have likely been suffering wear issues due to the road setup that a lot of people started with.
We might find that we can make a grippy tyre last a lot longer than they have been.


We're running -2.3º camber (max we could get from single adjustable camber pin) and still killing the shoulders on our tyres.

Here's a pic from Lakeside last week:
trackattack
Post #1027

22mm Front swaybars are now available, takes about 2 weeks to get them made.

trackattack
Post #1028

Sprints are on again Sunday 16th May at Lakeside Raceway.
All you need is a normal road car, long clothes and a helmet.

This is also the day of the Monster Car Show and Muscle Car Sprints
The Excel Series is also running on the 16th, check out the cheapest form of motorsport in the world !

More info follow this link - http://www.trackattack.com.au/sprints

Cheers Jeff
http://www.trackattack.com.au
Chunk
Post #1029

hmm... wishing there were a bit more parts availability for the old x2 now... doh!

trackattack
Post #1030

try qld hyundai parts or allbrand wrecking.
both are offering discounts to excel series cars.

Chunk
Post #1031

I was more referring to upgradable items such as swaybars

Replacement standard parts, yeah.. no probs :thumbsup:

trackattack
Post #1032

Send me a list of what you need and I will see what I can get.
we can definitely get springs and swaybars.

Chunk
Post #1033

cheers.. mainly after the swaybars. Springs I have sorted.

trackattack
Post #1034

Hire an Excel race Car through Mounfield Racing- $400 including entry fees and consumables.
Follow this link - http://www.trackattack.com.au/2010/index.p...;product=679980
Cheers Jeff
trackattack
Post #1035

I have found some more new wheels if anybody needs any - $105 per wheel pick up from Springwood.

Lotus - 15 x 6.5 - 4x114 38P
Profin - 15 x 6.0 - 4 x114 46P


Lotus Profin

Mounfield Racing
Post #1036

Mounfield Racing will debut one of their full prepared Excel Series cars at Lakeside on Sunday 16 May. These cars can be rented per day or for the entire series. We can even build a car to your specification. Come chat to Jeff or any of us guys.

trackattack
Post #1037

SEEKING EXPRESSIONS OF INTEREST FRONT WHEEL DRIVE TRAINING DAY LAKESIDE RACEWAY

Track Attack in Conjunction with Queensland Raceways is seeking expressions of interest in a Front Wheel Drive Training day at Lakeside Raceway.

* There will be a number of well known Racing Drivers there to provide tuition
* One of the Main instructors may include Glenn Seton - To Be Confirmed.
* The day will be FRONT WHEEL DRIVE ORIENTATED
* The Location will be Lakeside Raceway
* The cost will be around $200 per person
* All levels of experience will be catered for
* U Drive Rent a race cars may also be available

Date - TBC
Midweek or weekend - TBC subject to level of interest

Follow this link to add your name to the list of interested Drivers - CLICK HERE ! (there is no cost to nominate your interest)


Cheers Jeff
http://www.trackattack.com.au/training

NISMOgemini
Post #1038

what springs and shocks are proving to be the best option??

Mounfield Racing
Post #1039

QUOTE (NISMOgemini @ May 10 2010, 01:56 PM) *
what springs and shocks are proving to be the best option??



We were unable to find a suitable spring off the shelf, so Dobinson Springs in Rockhampton have rolled coils for us. Naturally our car has yet to run, so i am not suggesting they are the ants pants, but hopefully they will be appropriate. If the coil/strut package works, sets will be made available as a shelf item. Come see car 81 at Lakeside on its first run next Sunday.

NISMOgemini
Post #1040

i didn't think custom springs were allowed?

Beannie
Post #1041

anything is allowed :unsure: you'd be put into the modified class instead of the stock car class (which everyone is pretty much running in).

springs and shocks have to be "standard fitting parts that are readily available from retail outlets"
so custom made springs would make the car not eligble for stock car class.

nodrog
Post #1042

QUOTE (Beannie @ May 11 2010, 04:45 PM) *
anything is allowed :P you'd be put into the modified class instead of the stock car class (which everyone is pretty much running in).

springs and shocks have to be "standard fitting parts that are readily available from retail outlets"
so custom made springs would make the car not eligble for stock car class.



But then once they are a stock item available off the shelf, will the car then be able to run in the stock class???

NISMOgemini
Post #1043

as part of the excel series, my understanding is custom is not aloud.. fair enough they might become "off teh shelf" but currently they are not/would not be

Beannie
Post #1044

unfortunately will not be able to make this sunday may 16 event :P

next time :bowrofl:

slow bus
Post #1045

Side exhuast got done on the weekend, sound sweet not very loud at all, 2" from the flex through a open chamber muffler then dumped before the rear wheel.

Race seat and harness all sorted now just need some brakes and tyres. I wont be ready for the 16th, I guess I will have to wait for June.

For future reference fitting a race seat to hyundai rails is pain the in the arse. I drilled out the rivert holing the tilt mechanism got some 50x5 flat as cross bars and then bolted the seat to that.

I have 1 pair of camber bolts left over if anyone is intrested. Yours for only $20. Running both holes on the front and the top hole on the rear.

NISMOgemini
Post #1046

ill take the camber bolts.. u have pm

QUOTE (slow bus @ May 12 2010, 05:09 PM) *
Side exhuast got done on the weekend, sound sweet not very loud at all, 2" from the flex through a open chamber muffler then dumped before the rear wheel.

Race seat and harness all sorted now just need some brakes and tyres. I wont be ready for the 16th, I guess I will have to wait for June.

For future reference fitting a race seat to hyundai rails is pain the in the arse. I drilled out the rivert holing the tilt mechanism got some 50x5 flat as cross bars and then bolted the seat to that.

I have 1 pair of camber bolts left over if anyone is intrested. Yours for only $20. Running both holes on the front and the top hole on the rear.
police_chaser
Post #1047

Fvck me that looks like a lot of fun what do you think of the chances of creating a class series based on the Kia Grand Carnival?

Mounfield Racing
Post #1048

QUOTE (Beannie @ May 11 2010, 04:45 PM) *
anything is allowed :P you'd be put into the modified class instead of the stock car class (which everyone is pretty much running in).

springs and shocks have to be "standard fitting parts that are readily available from retail outlets"
so custom made springs would make the car not eligble for stock car class.



As I said we had springs manufactured by Dobinsons. They now have sets in stock for Hyundai's available to anyone direct from their ware house.

Innuendo
Post #1049

Shall be out this Sunday to sticky beak again, will bring the camera possibly though there already seems to be a line up of photographers.

Robby
Post #1050

QUOTE (slow bus @ May 12 2010, 05:09 PM) *
Side exhuast got done on the weekend, sound sweet not very loud at all, 2" from the flex through a open chamber muffler then dumped before the rear wheel.

Race seat and harness all sorted now just need some brakes and tyres. I wont be ready for the 16th, I guess I will have to wait for June.

For future reference fitting a race seat to hyundai rails is pain the in the arse. I drilled out the rivert holing the tilt mechanism got some 50x5 flat as cross bars and then bolted the seat to that.

I have 1 pair of camber bolts left over if anyone is intrested. Yours for only $20. Running both holes on the front and the top hole on the rear.



Check out the Mounfield Racing Car's pic on Mounfield Racing on facebook... There is pics of the modified seat mounts. Cutting and boxing the floor support and mounting the seats lower and better placed. Good way to spend a saturday in cutting up a hyundai!

  • Member Login

    If you have a BoostCruising account enter your user name and password into the yellow box.

    Alternatively, you can quickly login with Facebook.

    If you don't have an account create one below.

    Create Account
  • Forgotten your password?
  • Login with Facebook

    Login using your Facebook account!

Page 30 of 53
Jump to page
7 User(s) are reading this topic (7 Guests and 0 Anonymous Users)
0 Members:
Loading...
x